● 604-900-8174 · 24/7 EMERGENCY · GUILDFORD · FLEETWOOD · CLOVERDALE · ARRIVAL WINDOW ON THE CALL · NO HIDDEN FEES · LICENSED & INSURED · 604-900-8174 · 24/7 EMERGENCY · GUILDFORD · FLEETWOOD · CLOVERDALE · ARRIVAL WINDOW ON THE CALL · NO HIDDEN FEES · LICENSED & INSURED
Surrey.24/7 MOBILE
LOCKSMITH
Call 24/7604-900-8174

Door Lock Sticking or Won't Turn? Common Causes and Fixes

By Fast Locksmith Surrey · Nov 22, 2026
Residential Locksmith.Straight talk.

A deadbolt that sticks or won't turn is usually a dirty cylinder, a worn key, or a door that's shifted on its frame. Here's how to tell which one you've got and what actually fixes it.

Hand turning a stiff door lock key that is sticking in the deadbolt cylinder

Most sticking locks come down to one of three things: a dirty or worn cylinder, a key that's lost its shape, or a door that's shifted enough to throw the bolt out of line with the strike plate. Try a dry lock lubricant first, check the key on a spare, and if the bolt still binds, look at the door itself before you assume the lock is dying. If it's gotten worse fast, especially after cold weather or a rainy stretch, the door is probably the cause.

Why does my deadbolt only stick in certain weather?

Surrey gets a lot of wet weather from fall through spring, and a lot of homes here, especially older ones around Newton, Whalley, and Guildford, still have solid wood doors or wood frames. Wood absorbs moisture and swells. A door that fits fine in July can swell just enough by November that the bolt drags against the strike plate or doesn't line up at all.

You'll notice this pattern if the lock turns fine most of the year but gets stiff or jams every winter. That's not a locksmith problem first, it's a door problem. Planing the door edge or adjusting the strike plate usually fixes it, and a locksmith can do either, but so can a decent carpenter.

The key turns but the bolt won't move

If you can turn the key with no resistance but the bolt stays put, the problem is usually inside the lock body, not the cylinder. Common causes:

  • Broken or weak bolt spring. The spring that pushes the bolt in and out has given up. The cylinder still turns because it's disconnected from the mechanism.
  • Worn tailpiece. The small cam that connects the cylinder to the bolt mechanism has rounded off or snapped. This happens more on older, lower-grade hardware.
  • Stripped set screws. On some deadbolts the screw that holds the cylinder in place has backed out or stripped, so the cylinder spins without engaging anything.

None of these are a lubrication fix. They need the lock body opened up or replaced. A straightforward deadbolt swap typically runs 20 to 40 minutes on site, with parts and labour landing somewhere in the $90 to $180 range depending on the hardware grade you choose, as a typical range, not a quote. If you're replacing the lock anyway, it's worth knowing the difference between grades before you buy, which is covered in Deadbolt Grades Explained: What Grade 1, 2, and 3 Really Mean.

Dirty or gunked-up pins inside the cylinder

If the key goes in fine but feels gritty or the lock turns in fits and starts, the pin stack inside the cylinder is probably full of old lubricant, dust, and metal shavings from years of key wear. This builds up slowly, so people often don't notice until the lock is genuinely hard to operate.

Spray a dry lubricant, graphite powder or a PTFE-based product made for locks, into the keyway and work the key in and out a few times. Avoid WD-40 or any oil-based spray. It feels like it helps for a day or two, then it attracts dust and grit and turns into a paste that makes things worse. A proper cylinder clean and lube by a locksmith usually takes 20 to 30 minutes and typically costs $70 to $120, as a general range.

When it's the key, not the lock

Keys wear down. The ridges that push the pins to the right height get rounded off after years of use, especially if it's been duplicated from a duplicate. A worn key can bind in the lock even when the cylinder itself is fine.

Test this before you touch the lock: try your spare key. If the spare turns smoothly and the problem key doesn't, you've found your answer, and it's a $10 to $20 fix with a fresh key cut from the original. If you don't have a reliable original to copy, get one cut from a code or have the cylinder read, since copying a copy just carries the same wear forward.

Door alignment and strike plate problems

This is the one people miss most often. Hinges loosen over time, especially on exterior doors that get used several times a day. As the door sags even slightly, the bolt stops lining up with the hole in the strike plate, so it drags, binds, or won't extend at all.

  • Check the hinges first. Tighten any loose screws. If the holes are stripped, longer screws into the frame stud usually solve it.
  • Look at the strike plate. Marks or scrapes on the plate show you exactly where the bolt is hitting instead of sliding in clean.
  • Try the door with the deadbolt unlocked. If the door itself is hard to close flush, the problem is alignment, not the lock.

Adjusting or relocating a strike plate is usually a 15 to 25 minute job, often done alongside a lock service call rather than billed on its own.

What to try before you call anyone

Start simple. Use a dry lubricant, not oil. Test your spare key. Check the hinges and strike plate for obvious wear or looseness. If the lock still sticks after that, or if it's gotten suddenly worse, stop forcing the key. Forcing a stiff lock is how keys snap off inside the cylinder, which turns a simple fix into a more awkward one.

If you've tried the basics and the deadbolt still binds, turns partway, or won't retract, it's worth getting someone to look at the lock body itself rather than keep working a key that might snap. Have the lock's brand and the door type (wood, steel, fibreglass) ready when you call, since that affects what hardware fits. Fast Locksmith Surrey handles cylinder repairs, deadbolt replacement, and strike plate adjustments as straightforward house calls, no need to pull the door off yourself first.

Frequently asked questions

Why did my lock suddenly stop working with no warning?

A sudden failure, as opposed to gradual stiffness, usually means something broke inside, like a spring or tailpiece, rather than normal wear building up. It can also mean a key snapped off inside the cylinder. Either way it needs the lock opened up rather than lubricated.

Can I fix a sticking deadbolt myself?

Often yes, if it's dirt or a worn key. Dry lubricant and testing a spare key solves a good number of cases. If the bolt itself won't extend or retract, or the cylinder spins freely, that's an internal part failure and needs a locksmith or a lock replacement.

Will WD-40 fix a sticking lock?

No, and it usually makes things worse over time. It's an oil-based lubricant, so it attracts dust and grit inside the cylinder and gums up the pins after a short while. Use a graphite or PTFE-based lock lubricant instead.

  • sticking lock
  • deadbolt repair
  • lock maintenance
  • Surrey locksmith
► Keep reading

More from the blog.

Further reading from the same technicians.

Locked out right now? Just call.

604.900.8174 →
© 2026 Fast Locksmith Surrey · All rights reserved
Book online
Website by Linq field service software Websites, bookings, dispatch, marketing for small businesses. LINQSYSTEM.COM Create yours →